Load
How trace rates a session
4 min read
Every session gets a number for its load in trace. It combines duration and intensity and puts cycling, running and other sports on one common scale. Fitness, fatigue and form are built from this number.
Key points
- One hour flat out at your threshold gives 100 points of load. In trace the number is called TSS, for runs rTSS.
- trace takes the most precise measurement a session has, power first, then pace, then heart rate.
- Intensity counts more than proportionally. Half an hour at threshold loads you almost as much as an easy hour.
- How the session felt does not enter the load. trace compares it with what was planned.
One scale for every session
Whether a session was a lot or a little depends on two things, how long it lasted and how hard it was. trace combines both in one number. The yardstick is your threshold, the intensity you can hold for about an hour (Sitko et al., 2020). One hour exactly at that threshold gives 100 points. Andrew Coggan developed such a number for training with a power meter (Clarke & Skiba, 2013).
Intensity enters squared, so load grows faster than duration. One hour at 75 percent of threshold gives about 56 points, half an hour at threshold gives 50. Short hard sessions therefore weigh almost as much as long easy ones.
Which measurement counts
Many sessions come with more than one measurement. trace takes the most precise one and follows a fixed order.
- Power. If you ride with a power meter, trace uses normalized power, an average that weights hard sections more, and your threshold. The threshold is your critical power from the power curve or the value in your profile.
- Pace. For runs trace relates your pace to your threshold pace, which it derives from your best times. The number is then called rTSS.
- Heart rate. Without power or pace trace uses heart rate. The basis is Banister's training impulse, which weights duration by how high your heart rate is, the more strongly the closer it is to your maximum (Clarke & Skiba, 2013). trace calculates it from your average heart rate and scales it so that one hour at threshold again gives 100.
- Estimate. If there is no measurement at all, trace makes a cautious estimate from the duration of rides and runs, so a training day does not look like a rest day. Other sports such as hiking or strength training only count with measured heart rate.
This puts sessions with a power meter, a running watch and a heart rate strap on the same scale. An easy hour on the bike and an easy hour of running give similar numbers, and your weekly load shows all of your training.
Implausible recordings
Some recordings are broken, such as a forgotten watch that keeps running for two days or a power meter that reports thousands of watts. trace detects such values and calculates no load from them. A single session like that would otherwise distort fitness and form for weeks.
How it felt
After a session trace asks “How did it feel?”. Your answer on the scale from 1 to 10 does not enter the load, because power, pace and heart rate measure the effort more precisely. trace compares it with what was planned for the session and so sees whether an easy session turned out too hard or a hard one felt easier than expected.
That perceived effort is still worth a lot is shown by Carl Foster's method. The rating of the whole session times its duration in minutes is considered a valid and reliable measure of load, simple and without any device (Haddad et al., 2017).
Next article · 2.2
Fitness, fatigue and form
Fitness, fatigue and form describe how your training works over weeks. trace calculates them every day from the load of your sessions. With these three values you can see whether a block is building you up, whether recovery keeps pace and when your legs will be fresh for a race.
Related
Sources
- Clarke, D. C., & Skiba, P. F. (2013). Rationale and resources for teaching the mathematical modeling of athletic training and performance. Advances in Physiology Education, 37(2), 134–152. https://doi.org/10.1152/advan.00078.2011
- Haddad, M., Stylianides, G., Djaoui, L., Dellal, A., & Chamari, K. (2017). Session-RPE method for training load monitoring: Validity, ecological usefulness, and influencing factors. Frontiers in Neuroscience, 11, Article 612. https://doi.org/10.3389/fnins.2017.00612
- Sitko, S., Cirer-Sastre, R., Corbi, F., & López-Laval, I. (2020). Power assessment in road cycling: A narrative review. Sustainability, 12(12), Article 5216. https://doi.org/10.3390/su12125216